Asko refrigerator
showing E1
E1, E2 or E3 on an R31442I means one of its temperature sensors is defective.
Mon–Sat, 8am–8pm
- Sensor circuit
- Controls and sensors
- Source: ASKO
Book a visit
Three short steps, about a minute.
or call (844) 681-4650
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E1
actually means.
E1, E2 or E3 on an R31442I means one of its temperature sensors is defective. The manual does not say which number belongs to which sensor, only that the unit switches to safe mode and keeps a suitable temperature in every compartment on its own.
ASKO refrigerator display · also shown as E2, E3
What to do when E1 shows on the refrigeratorKind of codeSensor circuit
A temperature sensor reading outside its range, or the wiring to it. The reading is confirmed with a meter before any part is ordered.
Usually leads toControls and sensors
A refrigerator cools to what it believes the temperature is, and a sensor reading wrong is obeyed perfectly.
Shows up asRefrigerator Showing an Error Code
A code narrows the search, but only the manufacturer's own table gives it meaning.
MakeASKO
Scandinavian integrated refrigeration, mostly behind furniture panels.
SourceAsko Instructions for use, model R31442I, troubleshooting table (PDF on the Gorenje Group document server)
Asko R31442I. The RBR276 family reports its sensors with a lowercase t instead, and there E8 and E9 mean something else entirely.
Before you book,
in this order.
Each step comes from ASKO's own guidance for E1 on its refrigerators. Follow it to the end: the last card says whether this is a visit.
Note exactly which of the three numbers is on the display; the technician will ask for it.
Open the doors as little as you can while the appliance runs without a trustworthy sensor reading.
Book a visit, since Asko lists a defective sensor as repair work and safe mode stays on until it is done.
What not to do
It does not mean the settings are wrong. Turning the temperature up or down will not clear it, because the control is working around a defective sensor.
What you may
notice with it.
The refrigerator problem E1 tends to arrive with. Answer these at the refrigerator before anyone is booked.
All problems
Where E1 usually leads
Controls and sensors.
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesASKO
refrigerators.
Scandinavian integrated refrigeration, mostly behind furniture panels.
ASKO refrigerator repairMore ASKO codes
All 25 ASKO codesSensor circuit on other makes
Built-in refrigerator
Flush with the cabinets, serviced from the front, and almost always repaired rather than replaced.
Refrigerator column
Separate refrigerator and freezer towers, each with its own sealed system — so a failure stays on one side.
Undercounter refrigerator
A single 15 to 24 inch unit under the worktop — front-vented, tightly enclosed, and easily starved of air.
In ASKO's own words
Error code E1, E2 or E3 shown in the display. A temperature sensor is defective.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Asko R31442I. The RBR276 family reports its sensors with a lowercase t instead, and there E8 and E9 mean something else entirely.
ASKO E1 refrigerator repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E1.
Can I clear E1 myself?
Which sensor has failed when my Asko R31442I shows E1, E2 or E3?
Can I keep using the Asko R31442I with E1 on the display?
Back to your everyday
Still showing E1?
Book with the exact characters, the full model number, and whether it is still cooling — on a code, that is the whole starting point.