JennAir refrigerator
showing Call for Service
On a JennAir built-in refrigerator, a blinking Call for Service light is the control asking for a technician.
Mon–Sat, 8am–8pm
- Service indication
- Diagnostic visit
- Source: JennAir
Book a visit
Three short steps, about a minute.
or call (844) 681-4650
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Call for Service
actually means.
On a JennAir built-in refrigerator, a blinking Call for Service light is the control asking for a technician. JennAir suggests one thing first, a five-minute power reset at the breaker, and the light gives no hint of which part is involved.
JennAir refrigerator display
What to do when Call for Service shows on the refrigeratorKind of codeService indication
A light or a message asking for a visit. It says that something wants attention, not what, so the visit starts with a diagnosis.
Usually leads toDiagnostic visit
The visit that decides what the repair actually is, before any part is ordered.
Shows up asRefrigerator Showing an Error Code
A code narrows the search, but only the manufacturer's own table gives it meaning.
MakeJennAir
Panel-ready columns and built-in refrigeration with a strong design emphasis.
SourceJennAir Product Help (producthelp.jennair.com): Call for Service - Error Message - Built-In Refrigerator
JennAir documents this light for its built-in refrigerators.
Before you book,
in this order.
Each step comes from JennAir's own guidance for Call for Service on its refrigerators. Follow it to the end: the last card says whether this is a visit.
Switch the refrigerator off at the breaker and wait a full five minutes.
Switch it back on and watch the panel for a few minutes.
Over the next hours, check that both compartments are holding temperature.
If the light returns, book a visit and mention the Call for Service light on a built-in unit.
What not to do
It is not a reminder that a button press clears. A light that comes back after a full reset needs a technician.
What you may
notice with it.
The refrigerator problem Call for Service tends to arrive with. Answer these at the refrigerator before anyone is booked.
All problems
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesJennAir
refrigerators.
Panel-ready columns and built-in refrigeration with a strong design emphasis.
JennAir refrigerator repairMore JennAir codes
Service indication on other makes
Built-in refrigerator
Flush with the cabinets, serviced from the front, and almost always repaired rather than replaced.
Refrigerator column
Separate refrigerator and freezer towers, each with its own sealed system — so a failure stays on one side.
French door refrigerator
Two fresh-food doors over a freezer drawer — the most common premium layout, and the one with the most to go wrong at the door line.
In JennAir's own words
If the "Call for Service" light is blinking or flashing, try resetting the power to the unit:
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. JennAir documents this light for its built-in refrigerators.
JennAir Call for Service refrigerator repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Call for Service.
Can I clear Call for Service myself?
Does Call for Service on my JennAir built-in say which part is involved?
What should I check after resetting Call for Service on a JennAir?
Back to your everyday
Still showing Call for Service?
Book with the exact characters, the full model number, and whether it is still cooling — on a code, that is the whole starting point.