Liebherr refrigerator
showing F1 to F5
A number from F1 to F5 in the display means the appliance has detected a problem.
Mon–Sat, 8am–8pm
- Service indication
- Diagnostic visit
- Source: Liebherr
Book a visit
Three short steps, about a minute.
or call (844) 681-4650
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F1 to F5
actually means.
A number from F1 to F5 in the display means the appliance has detected a problem. Liebherr's manual does not say what each number stands for. It only asks you to have the number ready when you call customer service, so the service department is the one that reads it.
Liebherr refrigerator display · also shown as F1, F2, F3, F4, F5
What to do when F1 to F5 shows on the refrigeratorKind of codeService indication
A light or a message asking for a visit. It says that something wants attention, not what, so the visit starts with a diagnosis.
Usually leads toDiagnostic visit
The visit that decides what the repair actually is, before any part is ordered.
Shows up asRefrigerator Showing an Error Code
A code narrows the search, but only the manufacturer's own table gives it meaning.
MakeLiebherr
Refrigeration specialists: columns, integrated units and wine cabinets, with no cooking line at all.
SourceLiebherr Use and Care Manual, NoFrost combined refrigerator-freezer CS 1640 (7082 481-01), Liebherr service document PDF
Documented in Liebherr's manual for the CS 1640 NoFrost combined refrigerator-freezer. Other Liebherr models use different controls.
Before you book,
in this order.
Each step comes from Liebherr's own guidance for F1 to F5 on its refrigerators. Follow it to the end: the last card says whether this is a visit.
Write down the exact number shown (F1, F2, F3, F4 or F5).
Find the type designation and service details, and have them ready along with the number.
Check whether the compartments are still holding temperature.
Contact Liebherr customer service and give them the number.
What not to do
Be wary of lists online that assign each F number to a particular sensor. Liebherr's own manual does not decode them.
What you may
notice with it.
The refrigerator problem F1 to F5 tends to arrive with. Answer these at the refrigerator before anyone is booked.
All problems
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesLiebherr
refrigerators.
Refrigeration specialists: columns, integrated units and wine cabinets, with no cooking line at all.
Liebherr refrigerator repairMore Liebherr codes
Service indication on other makes
Built-in refrigerator
Flush with the cabinets, serviced from the front, and almost always repaired rather than replaced.
Refrigerator column
Separate refrigerator and freezer towers, each with its own sealed system — so a failure stays on one side.
Undercounter refrigerator
A single 15 to 24 inch unit under the worktop — front-vented, tightly enclosed, and easily starved of air.
In Liebherr's own words
If “F1” to “F5” appears in the display, the appliance has a fault. Have the fault number available
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Documented in Liebherr's manual for the CS 1640 NoFrost combined refrigerator-freezer. Other Liebherr models use different controls.
Liebherr F1 to F5 refrigerator repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F1 to F5.
Can I clear F1 to F5 myself?
What does F3 mean on my Liebherr, specifically?
What should I have ready before calling about F1 to F5 on a Liebherr?
Back to your everyday
Still showing F1 to F5?
Book with the exact characters, the full model number, and whether it is still cooling — on a code, that is the whole starting point.