

BlueStar refrigerator
showing High Temperature Alarm
On a BlueStar built-in refrigerator this alarm sounds without stopping once the fresh food side has been above 50°F, or the freezer above 20°F, for more than three hours.
Mon–Sat, 8am–8pm
- Service indication
- Diagnostic visit
- Source: BlueStar
Book a visit
Three short steps, about a minute.
or call (844) 681-4650
Loading appointment form…
The appointment form couldn’t load. Please try again.
What High Temperature Alarm
actually means.
On a BlueStar built-in refrigerator this alarm sounds without stopping once the fresh food side has been above 50°F, or the freezer above 20°F, for more than three hours. The home screen flashes dashes where that compartment's temperature normally shows, until it is back at the set point. The column models also beep and show a warning message when either compartment is too warm.
BlueStar refrigerator display
What to do when High Temperature Alarm shows on the refrigeratorKind of codeService indication
A light or a message asking for a visit. It says that something wants attention, not what, so the visit starts with a diagnosis.
Usually leads toDiagnostic visit
The visit that decides what the repair actually is, before any part is ordered.
Shows up asRefrigerator Not Cooling
The compartment is warm but the appliance still has power and still makes noise.
MakeBlueStar
An American maker known for its ranges, with built-in and column refrigeration made to match.
SourceBlueStar Built-In Refrigerator User Manual, part 250643 (bluestarcooking.com PDF): Alarms, Service
Limits and flashing dashes from the BlueStar built-in refrigerator manual (BBB36, BBBF36). BlueStar column models (manual R000045) show a warning message instead and give no limits.
Before you book,
in this order.
Each step comes from BlueStar's own guidance for High Temperature Alarm on its refrigerators. Follow it to the end: the last card says whether this is a visit.
Check that every door is closed and sealing, and think back to any recent power cut.
Measure the food temperature: three hours above the limit is enough to sort through perishables.
Watch whether the dashes give way to a temperature as the compartment recovers.
If the alarm returns or the compartment will not cool back down, book a visit.
What not to do
It is not the Call for Service message, which shows words alongside the dashes. It is also not the door alarm, which starts after a few minutes with a door open.
What you may
notice with it.
The refrigerator problems High Temperature Alarm tends to arrive with. Answer these at the refrigerator before anyone is booked.
All problems
Refrigerator Not Cooling
7 causes, cheapest first
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesBlueStar
refrigerators.
An American maker known for its ranges, with built-in and column refrigeration made to match.
BlueStar refrigerator repairMore BlueStar codes
Service indication on other makes
In BlueStar's own words
Sounds continuously when either the refrigerator temperature exceeds 50°F or the freezer exceeds 20°F for more than three hours.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Limits and flashing dashes from the BlueStar built-in refrigerator manual (BBB36, BBBF36). BlueStar column models (manual R000045) show a warning message instead and give no limits.
BlueStar High Temperature Alarm refrigerator repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about High Temperature Alarm.
Can I clear High Temperature Alarm myself?
What temperatures set off the BlueStar high temperature alarm?
Should I throw out food after the BlueStar high temperature alarm?
Back to your everyday
Still showing High Temperature Alarm?
Book with the exact characters, the full model number, and whether it is still cooling — on a code, that is the whole starting point.